Trying multiple recommendations listed on this forum, neither helped: holding for 10 seconds reset button while powering FX30: the RSA key is reset (fingerprint is different) but it keeps asking for root password instead of prompting to change it; trying AT RMARESET command: AT!RMARESET=1 !RMARES…

Does this help? [image] Factory Reset FX30 FX30 Thanks for the suggestion, but this command also didn’t work. After that, I connected through serial instead of ethernet, and I was able to use AT commands through that connection. I then reset the FX30, and I know that I su…

Unfortunately no. I have tried to do reset using following command: at!entercnd=“A710” at!rmareset=1 it didn’t help and still asking for the root password, that’s confusing.

Have you tried the (AT!FWD=FACTORYRECOVERY,ENABLE) command which enables factory reset via the push button? You can also see here [image] [FX30-4G LTE-M] Wrong /etc size in ls FW14 FX30 I tried the swiflash method on the R14 and it doesn’t work (as expected). In all cas…

Yes, I did it multiple times, to verify that it is enabled: … AT!FWD?FACTORYRECOVERY ENABLED OK … then press reset button, power ON the modem and keep pushing the reset button for >10seconds. On the next boot, the RSA key is different, but it still prompts for the root password instead of set…

How about this? [image] Swiflash -r broken with release 12 on wp77xx? Development tools According to the release note of fw r12, QTI9X07-2870 is to fix userapp partition being erased which is security hole. You might also try the following without downgrading to older ver…

unfortunately this can be done if I have ssh access to my modem… Could you please explain how to get access to linux shell using second UART? I don’t want to reconfigure working UART1, which is used for AT commands, because I will not be able to reset it. Also is there a way to reboot into bootloa…

you can turn the 2nd UART into console port by AT!MAPUART=16,2

Yeah, I know the command, sorry for the confusion. My question was about physical connection? If it’s over the same USB, I don’t see any new /dev/ttyUSB* after enabling that port with AT!MAPUART=16,2 In my case there are /dev/ttyUSB0, /dev/ttyUSB1 and /dev/ttyUSB2 The AT command service is on U…

I believe /dev/ttyusb2 is from the AT port of usb , noy uart And /dev/ttyusb0 and /dev/ttyusb1 are all from the usb port, not uart

you are right, /dev/ttyUSB2 is the AT port of usb. So, you are saying, that “AT!MAPUART” command will not have impact on behavior of the /dev/ttyUSB2, am I right? I still don’t understand how to connect to UART1 and 2 in order to start using them.

Need help with root password reset on FX30

IoT Gateways FX30

jyijyi September 14, 2024, 12:09am 6

How about this?

Topic		Replies	Views
[FX30 Cat-M] Modem won't connect after /mnt/userrw/ erasing FX30	36	1849	December 2, 2021
FX30S factory reset not working WP Series	2	744	December 21, 2022
No Root SSH ACCESS on WP7702 FX30 WP Series faq , fw-upgrade	27	273	June 30, 2025
FX30 stuck in reboot loop (less than 30 seconds) FX30	11	781	July 13, 2023
[Fx30] modem blocked after upraging the firmware release R13->R14 FX30	7	827	July 20, 2020

Need help with root password reset on FX30

Related topics