# \[WP7504\] Can't Reset User Parition via swiflash

**URL:** <https://forum.sierrawireless.com/t/wp7504-cant-reset-user-parition-via-swiflash/17262>\
**Category:** WP Series\
**Created:** [August 13, 2019, 5:20pm UTC](https://forum.sierrawireless.com/t/wp7504-cant-reset-user-parition-via-swiflash/17262 "2019-08-13T17:20:27Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![CoffeeMan64](https://sea1.discourse-cdn.com/flex025/user_avatar/forum.sierrawireless.com/coffeeman64/32/3995_2.png) [@CoffeeMan64](https://forum.sierrawireless.com/u/CoffeeMan64)\
**Post date:** [August 13, 2019, 5:20pm UTC](https://forum.sierrawireless.com/t/wp7504-cant-reset-user-parition-via-swiflash/17262/1 "2019-08-13T17:20:27Z")

</div>

Hi everyone,

I’m having an issue resetting the user partition on my WP7504 module. I’m using the command:

`swiflash -m "wp750x" -r`

It outputs the following:

`Detecting USB of the target`  
`DONE`  
`Communicating with the Target`  
`DONE`  
`Switching to firmware download mode`  
`......................................`

…and it just keeps outputting periods / dots forever. This is particularly strange, as I reset the user partition just last week without issue. However, I did attempt a new Legato platform installation on this device, so I’m wondering if there’s some factor there.

I’m using a dedicated Debian Linux install, so it’s not in a VM.

Thank you very much in advance for any possible advice/insight!

---

<div class="post-metadata">

**Author:** ![michael.roberts](https://avatars.discourse-cdn.com/v4/letter/m/e9c0ed/32.png) [@michael.roberts](https://forum.sierrawireless.com/u/michael.roberts)\
**Post date:** [February 4, 2020, 11:02pm UTC](https://forum.sierrawireless.com/t/wp7504-cant-reset-user-parition-via-swiflash/17262/2 "2020-02-04T23:02:21Z")

</div>

Hey CoffeeMan64,

I am having the same problem. I’m sure you’ve gotten past this by now, but I got around it by pulling the TP1 pin low before powering on the device. After about 2-3 minutes, I power cycle the device and let TP1 float again, which seems to work, but it’s really annoying. Did you ever resolve this?

---

<div class="post-metadata">

**Author:** ![cherokee](https://avatars.discourse-cdn.com/v4/letter/c/76d3ee/32.png) [@cherokee](https://forum.sierrawireless.com/u/cherokee)\
**Post date:** [February 8, 2020, 12:54pm UTC](https://forum.sierrawireless.com/t/wp7504-cant-reset-user-parition-via-swiflash/17262/3 "2020-02-08T12:54:10Z")

</div>

Hi @CoffeeMan64,

If you face this issue, forcing module to bootloader mode may be the best practice. Please try the part “Troubleshooting” at link below:  
[https://source.sierrawireless.com/resources/airprime/software/swiflash/#sthash.28kkbZ2p.dpbs](https://source.sierrawireless.com/resources/airprime/software/swiflash/#sthash.28kkbZ2p.dpbs)

Thanks,
