# Why I cannot see user LED selection in Resourse **URL:** \ **Category:** Octave\ **Created:** [October 11, 2021, 5:30am UTC](https://forum.sierrawireless.com/t/why-i-cannot-see-user-led-selection-in-resourse/25157 "2021-10-11T05:30:09Z")\ **Posts on this page:** 12\ **Page:** 1
**Author:** ![takashi\_shiina](https://avatars.discourse-cdn.com/v4/letter/t/e9bcb4/32.png) [@takashi\_shiina](https://forum.sierrawireless.com/u/takashi_shiina)\ **Post date:** [October 11, 2021, 5:30am UTC](https://forum.sierrawireless.com/t/why-i-cannot-see-user-led-selection-in-resourse/25157/1 "2021-10-11T05:30:09Z")
I bought FX30 with WP7702 module. I can register it to Octave. To check LED operation, I performed 1-7 operation on “2. Commanding Resources” in the following URL. > **[Getting Started : FX30](https://docs.octave.dev/docs/getting-started-with-the-fx30)** > > In this tutorial, we'll use Octave to: observe the value of the Analog Input available on the power connector of the FX30 used as a sensor value; generate repeated events for these sensor values; forward the data to an external cloud service... But I did not see green and led resource in Resource windows. I can see any value in io/config. To see two resource making Service, what part should I check Octave or FX30? ---
**Author:** ![djudkins](https://avatars.discourse-cdn.com/v4/letter/d/7ea924/32.png) [@djudkins](https://forum.sierrawireless.com/u/djudkins)\ **Post date:** [October 11, 2021, 4:28pm UTC](https://forum.sierrawireless.com/t/why-i-cannot-see-user-led-selection-in-resourse/25157/2 "2021-10-11T16:28:04Z")
Hello Takashi, You should see these resources. ![image](https://us1.discourse-cdn.com/flex025/uploads/sierrawireless/original/2X/2/2f6e3c459d32b706c619102698d449cc7641949d.png) You configure these via Services → GPIO ![image](https://us1.discourse-cdn.com/flex025/uploads/sierrawireless/original/2X/2/234f619b5027d787d0fa00a82c3c1107e13f6ec8.png) Also, See this forum entry: > [@Octave 3.20 FX30S Green signal and Red power LED - how to turn them off](https://forum.sierrawireless.com/t/octave-3-20-fx30s-green-signal-and-red-power-led-how-to-turn-them-off/24324): > > Hi I would like to minimise FX30S current consumption by turning of all LEDs. How do I turn off the cellular network (Green) LED ? I have tried using the following resources LED\_PWR\_RED does turn of the RED led but LED\_PWR\_GRN does not turn off the green LED Resource "/io/config" { "devs": [ { "conf": [ { "cntr": 0, "name": "EXT\_IO2\_AI", "res": "EXT\_IO2\_AI", "type": "AI", "unit": "none" }, { "na… I hope this solves your issue. ---
**Author:** ![djudkins](https://avatars.discourse-cdn.com/v4/letter/d/7ea924/32.png) [@djudkins](https://forum.sierrawireless.com/u/djudkins)\ **Post date:** [October 11, 2021, 4:31pm UTC](https://forum.sierrawireless.com/t/why-i-cannot-see-user-led-selection-in-resourse/25157/3 "2021-10-11T16:31:35Z")
You can find usage information on FX30 LEDs here: > **[GPIO Guides](https://docs.octave.dev/docs/gpio-guides#setting-the-fx30-led-colors-via-gpio)** > > This topic describes how to configure a GPIO pin in Octave and verify that Octave can control/monitor it. This process is necessary to identify a device's pin in Octave as either input or output and whether it is analog or digital. Once complete, the... ---
**Author:** ![takashi\_shiina](https://avatars.discourse-cdn.com/v4/letter/t/e9bcb4/32.png) [@takashi\_shiina](https://forum.sierrawireless.com/u/takashi_shiina)\ **Post date:** [October 12, 2021, 12:23am UTC](https://forum.sierrawireless.com/t/why-i-cannot-see-user-led-selection-in-resourse/25157/4 "2021-10-12T00:23:07Z")
Thanks, But I did not see green/red in my Resources. My process is: 1. Set GPIO output for LED\_USR\_GRN and LED\_USR\_RED 2. Go to Resources screen and check io note. 3. But I did not see green and red1 node. Please see my screen and advise next confirmation. Note: I use FX30 with WP7702 module now. ![pic_1](https://us1.discourse-cdn.com/flex025/uploads/sierrawireless/original/2X/9/9633895ed159e8217cd4782117341af4dad22fc2.jpeg) ![pic_2](https://us1.discourse-cdn.com/flex025/uploads/sierrawireless/original/2X/4/4abb1fcd22d74b341e0d865095abc6145d801721.jpeg) ---
**Author:** ![djudkins](https://avatars.discourse-cdn.com/v4/letter/d/7ea924/32.png) [@djudkins](https://forum.sierrawireless.com/u/djudkins)\ **Post date:** [October 12, 2021, 6:42pm UTC](https://forum.sierrawireless.com/t/why-i-cannot-see-user-led-selection-in-resourse/25157/5 "2021-10-12T18:42:08Z")
Hello Takashi, I believe there is a bug in the Octave UI. If you use anything other than the default: “name”: “LED\_USR\_GRN”, **"res": “LED\_USR\_GRN”,** “type”: “DO” }, { “name”: “LED\_USR\_RED”, **"res": “LED\_USR\_RED”,** “type”: “DO” }, The LED resources will not appear in the resource tree unless you use the default names… Please use the default names now for a workaround to the issue. I will submit a ticket to engineering . ![image](https://us1.discourse-cdn.com/flex025/uploads/sierrawireless/original/2X/a/a3a4c122a84337c837b78a877e1a02486757008e.png) ---
**Author:** ![djudkins](https://avatars.discourse-cdn.com/v4/letter/d/7ea924/32.png) [@djudkins](https://forum.sierrawireless.com/u/djudkins)\ **Post date:** [October 12, 2021, 7:25pm UTC](https://forum.sierrawireless.com/t/why-i-cannot-see-user-led-selection-in-resourse/25157/6 "2021-10-12T19:25:36Z")
Highly recommend you upgrade FX 30 device to firmware 3.2.0 or higher. This issue appears to have been fixed. ---
**Author:** ![takashi\_shiina](https://avatars.discourse-cdn.com/v4/letter/t/e9bcb4/32.png) [@takashi\_shiina](https://forum.sierrawireless.com/u/takashi_shiina)\ **Post date:** [October 14, 2021, 7:40am UTC](https://forum.sierrawireless.com/t/why-i-cannot-see-user-led-selection-in-resourse/25157/7 "2021-10-14T07:40:14Z")
Thanks. I tried to update Octave 3.3.0 from 3.1.0. I select Firmwares in DEVICE-\>details and select 3.3.3 and press “DEPLOY” button. I think that FX30 tried to update FW by FOTA. But… FOTA did not finish after 3 hour. Module signal is stopping for 1 hour. How to recovery this behavior. Note: I connect USB cable and send AT command. Then, module returned the attached file response. I think that FOTA is succeeded but carrier image is difference. So, FX30 cannot connect network and Octave cannot receive correct information from FX30. I’m using FX30 on Japan. So, I would like to set default image for Octave. Please let us know how to recovery it. My FX30 SKU is 1104665. ---
**Author:** ![takashi\_shiina](https://avatars.discourse-cdn.com/v4/letter/t/e9bcb4/32.png) [@takashi\_shiina](https://forum.sierrawireless.com/u/takashi_shiina)\ **Post date:** [October 14, 2021, 7:42am UTC](https://forum.sierrawireless.com/t/why-i-cannot-see-user-led-selection-in-resourse/25157/8 "2021-10-14T07:42:23Z")
I attached Log file, please advise it.[AT\_commad\_log.txt](https://forum.sierrawireless.com/uploads/short-url/358UATXizQbjjyWqX336andaE1G.txt) (2.6 KB) ---
**Author:** ![njoyeux](https://sea1.discourse-cdn.com/flex025/user_avatar/forum.sierrawireless.com/njoyeux/32/6714_2.png) [@njoyeux](https://forum.sierrawireless.com/u/njoyeux)\ **Post date:** [October 14, 2021, 9:13am UTC](https://forum.sierrawireless.com/t/why-i-cannot-see-user-led-selection-in-resourse/25157/9 "2021-10-14T09:13:10Z")
Hi Takashi-san, The log you attached shows the device has received the ATT 3.3.0 binary, whereas it should be SIERRA 3.3.0. I need to check with the Octave back-end team why this happened. Do you use an ECC SIM card ? Meanwhile you can recover your FX30 by updating it locally: > **[Upgrade a Device Locally with the Latest Firmware](https://docs.octave.dev/docs/upgrade-a-device-locally-with-the-latest-firmware)** > > This page provides instructions to upgrade your Octave device with the latest firmware using your local development PC. Alternatively you can upgrade your device over the air if your device has been set up to communicate with Octave. Windows Host You... Please select the 3.3.0 FX30 version (not the ATT one) Regards, Nicolas ---
**Author:** ![njoyeux](https://sea1.discourse-cdn.com/flex025/user_avatar/forum.sierrawireless.com/njoyeux/32/6714_2.png) [@njoyeux](https://forum.sierrawireless.com/u/njoyeux)\ **Post date:** [October 14, 2021, 9:24am UTC](https://forum.sierrawireless.com/t/why-i-cannot-see-user-led-selection-in-resourse/25157/10 "2021-10-14T09:24:10Z")
Hi Takashi-san, Our system (Airvantage) indicates that you are using ATT network in Japan, with an ATT sim card. This is why the system picked up the ATT Firmware version. Can you explain how your offer works ? Why should you not use the ATT APN ? Thanks Nicolas ---
**Author:** ![takashi\_shiina](https://avatars.discourse-cdn.com/v4/letter/t/e9bcb4/32.png) [@takashi\_shiina](https://forum.sierrawireless.com/u/takashi_shiina)\ **Post date:** [October 15, 2021, 8:49am UTC](https://forum.sierrawireless.com/t/why-i-cannot-see-user-led-selection-in-resourse/25157/11 "2021-10-15T08:49:13Z")
After updating FW for SWI, I can control user LED. When I control LED\_USR\_GRN for GPIO48, FX30 is changed Red. When I control LED\_USR\_RED for GPIO47, FX30 is changed green. Why my environment is mixing LED control between Red and Green? I used latest FW 3.3.0 now. ---
**Author:** ![djudkins](https://avatars.discourse-cdn.com/v4/letter/d/7ea924/32.png) [@djudkins](https://forum.sierrawireless.com/u/djudkins)\ **Post date:** [October 25, 2021, 3:54pm UTC](https://forum.sierrawireless.com/t/why-i-cannot-see-user-led-selection-in-resourse/25157/12 "2021-10-25T15:54:03Z")
Hello Takashi, Please see this link for controlling FX30 LED colors: > **[GPIO Guides](https://docs.octave.dev/docs/gpio-guides#setting-the-fx30-led-colors-via-gpio)** > > This topic describes how to configure a GPIO pin in Octave and verify that Octave can control/monitor it. This process is necessary to identify a device's pin in Octave as either input or output and whether it is analog or digital. Once complete, the...