# Problems running Tlemetry samle .CREG=0,2

**URL:** <https://forum.sierrawireless.com/t/problems-running-tlemetry-samle-creg-0-2/3636>\
**Category:** Legacy AirPrime modules\
**Created:** [September 15, 2009, 5:47pm UTC](https://forum.sierrawireless.com/t/problems-running-tlemetry-samle-creg-0-2/3636 "2009-09-15T17:47:35Z")\
**Posts on this page:** 6\
**Page:** 1

<div class="post-metadata">

**Author:** ![nicool67](https://avatars.discourse-cdn.com/v4/letter/n/b3f665/32.png) [@nicool67](https://forum.sierrawireless.com/u/nicool67)\
**Post date:** [September 15, 2009, 5:47pm UTC](https://forum.sierrawireless.com/t/problems-running-tlemetry-samle-creg-0-2/3636/1 "2009-09-15T17:47:35Z")

</div>

Hello people!!, i want to send and recieve messages from my q2686 with a test board. Qhen i run Telemetry.c i cant make a registration ( +CREG=0,2). But the strage thing is that the SIM card works fine in a cell phone, and the signal level is aparently OK (+CSQ= 12,0). Can anyone gove me a hand?.

Than you for advance.

---

<div class="post-metadata">

**Author:** ![awneil](https://avatars.discourse-cdn.com/v4/letter/a/49beb7/32.png) [@awneil](https://forum.sierrawireless.com/u/awneil)\
**Post date:** [September 15, 2009, 6:45pm UTC](https://forum.sierrawireless.com/t/problems-running-tlemetry-samle-creg-0-2/3636/2 "2009-09-15T18:45:27Z")

</div>

Do you have the correct frequency band(s) selected?

---

<div class="post-metadata">

**Author:** ![davidc](https://avatars.discourse-cdn.com/v4/letter/d/a183cd/32.png) [@davidc](https://forum.sierrawireless.com/u/davidc)\
**Post date:** [September 15, 2009, 11:54pm UTC](https://forum.sierrawireless.com/t/problems-running-tlemetry-samle-creg-0-2/3636/3 "2009-09-15T23:54:15Z")

</div>

Hiya,

Do you have a good antenna? Is the module making a good connection with the dev board? You really should solder at least one of the ground pins on the Q2686 module to the dev board - the pin closest to the antenna connection is a good one.

ciao, Dave

---

<div class="post-metadata">

**Author:** ![awneil](https://avatars.discourse-cdn.com/v4/letter/a/49beb7/32.png) [@awneil](https://forum.sierrawireless.com/u/awneil)\
**Post date:** [September 16, 2009, 6:36am UTC](https://forum.sierrawireless.com/t/problems-running-tlemetry-samle-creg-0-2/3636/4 "2009-09-16T06:36:26Z")

</div>

If it’s on a custom board, check very carefully with an oscilloscope that the power supply is absolutely solid!

See: [viewtopic.php?f=29&t=3152&p=11704&hilit=oscilloscope#p11704](http://www.wavecom.com/modules/movie/scenes/forums/viewtopic.php?f=29&t=3152&p=11704&hilit=oscilloscope#p11704)

As the unit starts up, the point where it tries to GSM register is the first time that it really draws its full current - so, if you have a power supply problem, that is likely to be the point at which it will show-up.

If the power supply “dips” - even momentarily - while the unit is transmitting, that is very liekly to cause the registration to fail.

---

<div class="post-metadata">

**Author:** ![nicool67](https://avatars.discourse-cdn.com/v4/letter/n/b3f665/32.png) [@nicool67](https://forum.sierrawireless.com/u/nicool67)\
**Post date:** [September 16, 2009, 8:31pm UTC](https://forum.sierrawireless.com/t/problems-running-tlemetry-samle-creg-0-2/3636/5 "2009-09-16T20:31:14Z")

</div>

Its working!!! 😃 . It was a hardware problem!!!. Thank you so much for the replies. I can send sms with the AT comands and make a GPRS client too!!. If anyone needs the code please send me a personal message or a email.

Thanks again!!!.

---

<div class="post-metadata">

**Author:** ![nicool67](https://avatars.discourse-cdn.com/v4/letter/n/b3f665/32.png) [@nicool67](https://forum.sierrawireless.com/u/nicool67)\
**Post date:** [September 18, 2009, 3:23pm UTC](https://forum.sierrawireless.com/t/problems-running-tlemetry-samle-creg-0-2/3636/6 "2009-09-18T15:23:51Z")

</div>

It seems that the power supply wasnt rith enough. I must have as nominal 3.6V and i was having 3.1V.
