# MC7354 - how to enable AGPS and check

**URL:** <https://forum.sierrawireless.com/t/mc7354-how-to-enable-agps-and-check/7489>\
**Category:** MC/EM Series\
**Created:** [October 7, 2014, 7:05pm UTC](https://forum.sierrawireless.com/t/mc7354-how-to-enable-agps-and-check/7489 "2014-10-07T19:05:26Z")\
**Posts on this page:** 4\
**Page:** 1

<div class="post-metadata">

**Author:** ![okqqkimo1](https://avatars.discourse-cdn.com/v4/letter/o/f1d935/32.png) [@okqqkimo1](https://forum.sierrawireless.com/u/okqqkimo1)\
**Post date:** [October 7, 2014, 7:05pm UTC](https://forum.sierrawireless.com/t/mc7354-how-to-enable-agps-and-check/7489/1 "2014-10-07T19:05:26Z")

</div>

I have two question.

First :

How can I enable AGPS used AT command for MC7354 ?  
I want to use AT!GPSLOC? to get location, but the lantence too long,  
so I want to enable AGPS function.

Second:

How can I check the AGPS function is running?

---

<div class="post-metadata">

**Author:** ![Rex\_alex](https://avatars.discourse-cdn.com/v4/letter/r/73ab20/32.png) [@Rex\_alex](https://forum.sierrawireless.com/u/Rex_alex)\
**Post date:** [October 8, 2014, 11:57am UTC](https://forum.sierrawireless.com/t/mc7354-how-to-enable-agps-and-check/7489/2 "2014-10-08T11:57:37Z")

</div>

hi,

I think you can use at!GPSSUPLURL to set the SUPL url… and probably after that you need to start the gps fix… i have to run the test at my end once for this… but this command should work…

---

<div class="post-metadata">

**Author:** ![okqqkimo1](https://avatars.discourse-cdn.com/v4/letter/o/f1d935/32.png) [@okqqkimo1](https://forum.sierrawireless.com/u/okqqkimo1)\
**Post date:** [October 8, 2014, 4:40pm UTC](https://forum.sierrawireless.com/t/mc7354-how-to-enable-agps-and-check/7489/3 "2014-10-08T16:40:29Z")

</div>

Hi Rex\_alex  
Yes, I used the GPSSUPLURL command, but the time is 26s-40s.  
When I check the AGPS wiki, the AGPS has cold start / warm start / hot start mode.  
I think that I need the hot start mode, because it can less than 10s.  
But I can not find about the AGPS doc for MC73xx, did you have any suggestion?

did I need enable !GPSKEEPWARM?  
When I set the “AT!GPSKEEPWARM=1”, the value always return 0 (such as KeepWarm Enabled: 0 Warm Status: 0).

The step is my AGPS setting flow:

1. AT!ENTERCND=“A710”
2. AT!GPSPOSMODE=7F
3. AT!GPSSUPLURL=“[supl.google.com](http://supl.google.com)”
4. AT!GPSPORTID=7276
5. AT!GPSTRANSSEC=0

Thanks

---

<div class="post-metadata">

**Author:** ![okqqkimo1](https://avatars.discourse-cdn.com/v4/letter/o/f1d935/32.png) [@okqqkimo1](https://forum.sierrawireless.com/u/okqqkimo1)\
**Post date:** [September 9, 2015, 11:43pm UTC](https://forum.sierrawireless.com/t/mc7354-how-to-enable-agps-and-check/7489/4 "2015-09-09T23:43:51Z")

</div>

have any update?

I still fail on the test case…  
Or do you have gpsone xtra test SOP?