# HL78 AT+GNSSNMEA=4 datamode shows nothing on terminal

**URL:** <https://forum.sierrawireless.com/t/hl78-at-gnssnmea-4-datamode-shows-nothing-on-terminal/32377>\
**Category:** MC/EM Series\
**Created:** [May 22, 2024, 1:31pm UTC](https://forum.sierrawireless.com/t/hl78-at-gnssnmea-4-datamode-shows-nothing-on-terminal/32377 "2024-05-22T13:31:11Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![lsmtech](https://avatars.discourse-cdn.com/v4/letter/l/ac91a4/32.png) [@lsmtech](https://forum.sierrawireless.com/u/lsmtech)\
**Post date:** [May 22, 2024, 1:31pm UTC](https://forum.sierrawireless.com/t/hl78-at-gnssnmea-4-datamode-shows-nothing-on-terminal/32377/1 "2024-05-22T13:31:11Z")

</div>

when I use AT+GNSSNMEA=4 datamode shows nothing on terminal. I have usb connected to uart 1 and I perform the commands as follows: AT+GNSSNMEA=0,1000,0,73 first, then AT+GNSSSTART=0, and lastly AT+GNSSNMEA=4. Once the terminal prints connect nothing then appears.

It is very weird as I have seen it print out gps information in the past. I am not sure if the datamode is still on a session or what. I use +++ when I try to exit out. However sometimes that does not work and I have to made a hard reset on the device so I am not sure if maybe that messed with the datamode since it did not properly escape in the past.

Any suggestions? my current software version is 5.4.12 when I use the ati8 command.

---

<div class="post-metadata">

**Author:** ![jerdung](https://avatars.discourse-cdn.com/v4/letter/j/82dd89/32.png) [@jerdung](https://forum.sierrawireless.com/u/jerdung)\
**Post date:** [May 31, 2024, 8:57am UTC](https://forum.sierrawireless.com/t/hl78-at-gnssnmea-4-datamode-shows-nothing-on-terminal/32377/2 "2024-05-31T08:57:49Z")

</div>

Hi @lsmtech,

Please refer to pages 2 and 3 of the AirPrime HL78xx GNSS Behavior document at the following link for GNSS Operational: [AirPrime - HL78xx - GNSS Behavior](https://source.sierrawireless.com/resources/airprime/application_notes_and_code_samples/airprime_hl78xx_gnss_behavior/#sthash.9FVylUbU.dpbs)

The GNSS receiver and LTE/GSM receiver share the same RF resources, therefore GNSS can only be used when the module is not actively connected on LTE/GSM.

Thanks,

---

<div class="post-metadata">

**Author:** ![lsmtech](https://avatars.discourse-cdn.com/v4/letter/l/ac91a4/32.png) [@lsmtech](https://forum.sierrawireless.com/u/lsmtech)\
**Post date:** [June 11, 2024, 8:00pm UTC](https://forum.sierrawireless.com/t/hl78-at-gnssnmea-4-datamode-shows-nothing-on-terminal/32377/3 "2024-06-11T20:00:20Z")

</div>

Hey jerdung,

Thanks for the link. Sorry for the late response but the document did not seem to work for me. It said that AT+GNSSSTART=0 would return \* “+GNSSEV: 1,0” if gnss could not activate. However when I used the command the 2 responses below is what I get.  
+GNSSEV: 0,1  
+GNSSEV: 1,1  
So I think that my lte is not affecting my gps. However the AT+GNSSNMEA=4 is still causing issues with datamode not printing out anything, nor do I get any response when using “+++” command.

perhaps it is my firm ware. Is there a way to update the firmware using Mac OS?
